Btrfs supports transparent file compression. There are two algorithms available, ZLIB and LZO. Basically, compression is on a file by file basis. You can have a single btrfs mount point that has some files that are uncompressed, some that are compressed with LZO, some with ZLIB, for instance (though you may not want it that way, it is supported).
How do I enable compression?
-o compress or
-o compress-force. Then write (or re-write) files, and they will be transparently compressed. Some files may not compress very well, and these are typically not recompressed but still written uncompressed. See the What happens to incompressible files? section, below.
What is the default compression method?
As for kernels up to 3.6 it's ZLIB.
What are the differences between compression methods?
There's a speed/ratio trade-off:
- ZLIB -- slower, higher compression ratio (uses zlib level 3 setting, you can see the zlib level difference between 1 and 6 in zlib sources).
- LZO -- faster compression and decompression than zlib, worse compression ratio, designed to be fast
The differences depend on the actual data set and cannot be expressed by a single number or recommendation. Do your own benchmarks. LZO seems to give satisfying results for general use.
Are there other compression methods supported?
Currently no, there is a work in progress to add LZ4. The difference is a plan to add also its high compression mode that is slow but achieves better compression ratio while the decompressor remains the same and the decompression speed is unaffected (see here and also the High Compression (HC) mode here). It has not yet been accepted, however, see here.
Snappy support (compresses slower than LZ0 but decompresses much faster) has also been proposed. Some work has been done toward adding lzma (very slow, high compression) support as well. Current status is "not considered anymore"
Can a file data be compressed with different methods?
Yes. The compression algorithm is stored per-extent.
How can I determine compressed size of a file?
compsize takes a list of files on a btrfs filesystem and measures used compression types and effective compression ratio: https://github.com/kilobyte/compsize
There is a patch adding support fort that, currently it's not merged. You can kind of guess at its compressed size by comparing the output from the
df command before and after writing a file, if this is available to you.
Why does not
du report the compressed size?
Traditionally the UNIX/Linux filesystems did not support compression and there was no item in
stat data structure allocated for a similar purpose. There's the file size, that denotes nominal file size independent of the actually allocated size on-disk. For that purpose, the
stat.st_blocks item contains a value that corresponds to the number of blocks allocated, i.e. in case of sparse files. However, when a compression is involved, the actually allocated size may be smaller than nominal, although the file is not sparse.
There are utilities that determine sparseness of a file by comparing the nominal and block-allocated size, this behaviour might cause bugs if
st_blocks contained the amount after compression.
Another issue with backward compatibility is that up to now
st_blocks always contains the uncompressed number of blocks. It's unclear what would happen if there are files with mixed types of the value. The proposed solution is to add another special call for that (via
ioctl), but this may be not the ideal solution.
Can I determine what compression method was used on a file?
Not directly, but this is possible from a userspace tool without any special kernel support (the code just has not been written).
Can I force compression on a file without using the compress mount option?
Yes. The utility chattr supports setting file attribute c that marks the inode to compress newly written data. Setting the compression property on a file using
btrfs property set <file> compression <zlib|lzo> will force compression to be used on that file using the specified algorithm.
Can I disable compression on a file?
It is possible to disable compression of new extents on a file using the
btrfs property set <file> compression "" command. This will set the "no compression" flag on the file and newly written extents will not be compressed until the flag is cleared either by
chattr +c or by using the compression property to specify an algorithm. Already written extents will not be rewritten.
Can I set compression per-subvolume?
Currently no, this is planned. You can simulate this by enabling compression on the subvolume directory and the files/directories will inherit the compression flag.
What's the precedence of all the options affecting compression?
Compression to newly written data happens:
- always -- if the filesystem is mounted with
- never -- if the
NOCOMPRESSflag is set per-file/-directory
- if possible -- if the
COMPRESSper-file flag (aka
chattr +c) is set, but it may get converted to
- if possible -- if the
-o compressmount option is specified
Note, that mounting with
-o compress will not set the
+c file attribute.
How can I recursively compress/uncompress a directory (including guessed/forced-compression)
Uset the btrfs filesystem defrag command, the option -r will process the files recursively in a directory. This is independent of the mount options compress or compress-force, and using the option -c you can set the compression algorithm.
Currently (4.14), it's not possible to select "no compression", using the defrag command. This may change in the future.
How does compression interact with direct IO or COW?
Compression does not work with DIO, does work with COW and does not work for NOCOW files. If a file is opened in DIO mode, it will fall back to buffered IO.
Are there speed penalties when doing random access to a compressed file?
Yes. The compression processes ranges of a file of maximum size 128 KiB and compresses each 4 KiB (or page-sized) block separately. Accessing a byte in the middle of the given 128 KiB range requires to decompress the whole range. This is not optimal and is subject to optimizations and further development.
What happens to incompressible files?
There is a simple decision logic: if the first portion of data being compressed is not smaller than the original, the compression of the file is disabled -- unless the filesystem is mounted with
-o compress-force. In that case it'll be compressed always regardless of the compressibility of the file. This is not optimal and subject to optimizations and further development.
This means that many times, even if you have compression enabled, if the first portion of the file doesn't compress well, but the rest *does* it still won't compress the rest. Recommend using
-o compress-force if you really want compression enabled on a mounted filesystem, though if you have many differing types files, then just
-o compress might work well for you.